Stamp

CONVENTIONAL RUBBER STAMP MAKING EQUIPMENT

Thermogravor

Photopolymer machine

Photopolymer machine to process photopolymer liquid resin or hard photopolymer plates (Rigilon, Jet, etc) size A 4, made of 3 parts

Exposure unit

  • To make a negative film from a laser printed positive
  • To expose a hard photopolymer plate through a negative and get a master plate
  • To expose photopolymer liquid resin through a negative and get photopolymer stamps.

Wash-out unit

  • for hard photopolymer plates : exposed areas are left and create relief when uncured parts are washed away (depth)
  • for photopolymer liquid resin : exposed areas are left and create letters when uncured parts are washed away (depth).
  • Drying unit
  • for negative film
  • for hard photopolymer plate after washing-out
  • for photopolymer resin after washing-ou.

Drying unit

  • for negative film
  • for hard photopolymer plate after washing-out
  • for photopolymer resin after washing-ou

1. Exposure unit

Photopolymer Isolation

  • UV tubes with on/off digital timer with memory and buzzer
  • vacuum pump to keep positive and negative films or negative film and photopolymer material in close contact
  • glasses with closing /calibrating system to process liquid photoplymer
  • plastic tray with holding system to post expose photopolymer resin
  • compressor to pierce air bubbles in photopolymer resin

2. Wash-out unit

Wash-out unit

  • parts are in stainless steel
  • thermostat for water temperature control
  • timer to start the engraving unit
  • the engraving mechanism is outside water to avoid dirt and jamming problems of the moving part

3. Drying unit

Drying unit

  • 3 drying compartments
  • thermostat for temperature control
  • on/off timer

Automatic Press

Automatic press

Motorized moulding and vulcanizing press , size 350 x 300 mm, for rubber and pre-inked stamp making
All manufacturing steps are automatically performed . It is just necessary to set parameters (temperatures, preheating and cooking times, cooking pressure) Then, pushing a single key will automatically start the procedure : platen rising, contact during pre-heating time, degassing, pressure and cooking , opening when programmed time is over.

  • Pressure by motorized hydraulic pump, with separate jack to avoid heat transmission to hydraulic parts.
  • automatic control of manufacturing cycles
  • preheating and curing time are controlled by a digital timer
  • switch for additional degassing
  • emergency stop
  • manometer for pressure control
  • 2 PID electronic controllers securing perfect accuracy and distribution of temperature for pre-inked and rubber stamp making
  • platen sizes : standard : 350 x 300 mm or GF : 420 x 350 mm

PEVP Press A5

Moulding press size A5

Moulding and vulcanizing presses used to press types or photopolymer plate in a matrix board and get a mold in which rubber is molded
Size A5 (270 x 230 mm)

A5 PRESS

  • pressure is provided by coupled pump and jack
  • 2 PID electronic controllers secure perfect accuracy and distribution of temperature for pre-inked and rubber stamp making
  • Manual digital timer for cycle control

PEVP Press A4

Moulding press size A4

Moulding and vulcanizing presses used to press types or photopolymer plate in a matrix board and get a mold in which rubber is molded
A4 (350 x 300 mm)

A4 PRESS

  • pressure is provided by separate pump and jack
  • 2 PID electronic controllers secure perfect accuracy and distribution of temperature for pre-inked and rubber stamp making
  • Manual digital timer for cycle control
  • Manometer for pressure control on A 4 model.

LASER MANUFACTURING EQUIPMENT

ILS II

Laser engraver ILS2

  • Available 12, 30 or 50 W, size 410 x 295 mm (A3).
  • Motorized Z axis allows to process pieces up to 120 mm
  • Air assistance

ILS III

Laser engraver : ILS3

  • Available in 12, 30 , 50 or 100 W, size 610 x 457 mm (A2)
  • Openable front door
  • Autofocus.
  • Motorized Z axis allows to process pieces up to 210 mm
  • Red dot pointer
  • Air assistance

ILS IV

  • Available in 30, 50 or 100 W, size t 1000 x 600 mm.
  • traversing-door design
  • Autofocus.
  • Motorized Z axis allows to process pieces up to 210 mm .
  • Red dot pointer
  • Air assistance
  • ethernet connectivity