Equipment for rubber stamp maker : photopolymer unit, hydraulic press, laser engraver

Stamp

Rubber stamp / Pre inked stamp / Photopolymer stamp

Manufacturing technics

equipment

products

literature (pdf file)

CONVENTIONAL RUBBER STAMP MAKING EQUIPMENT

Thermogravor

Photopolymer machine to process photopolymer liquid resin or hard photopolymer plates (Rigilon, Jet, etc)
size A 4, made of 3 parts :

Exposure unit

to make a negative film from a laser printed positive
to expose a hard photopolymer plate through a negative and get a master plate
to expose photopolymer liquid resin through a negative and get photopolymer stamps.

Wash-out unit

for hard photopolymer plates : exposed areas are left and create relief when uncured parts are washed away (depth)
for photopolymer liquid resin : exposed areas are left and create letters when uncured parts are washed away (depth).

Drying unit

for negative film
for hard photopolymer plate after washing-out
for photopolymer resin after washing-ou

1. Exposure unit

UV tubes with on/off digital timer with memory and buzzer
vacuum pump to keep positive and negative films or negative film and photopolymer material in close contact
glasses with closing /calibrating system to process liquid photoplymer
plastic tray with holding system to post expose photopolymer resin
compressor to pierce air bubbles in photopolymer resin

2. Wash-out unit

parts are in stainless steel
thermostat for water temperature control
timer to start the engraving unit
the engraving mechanism is outside water to avoid dirt and jamming problems of the moving part

3. Drying unit

3 drying compartments
thermostat for temperature control
on/off timer

Automatic press

Motorized moulding and vulcanizing press , size 350 x 300 mm, for rubber and pre-inked stamp making
All manufacturing steps are automatically performed . It is just necessary to set parameters (temperatures, preheating and cooking times, cooking pressure) Then, pushing a single key will automatically start the procedure : platen rising, contact during pre-heating time, degassing, pressure and cooking , opening when programmed time is over.

Pressure by motorized hydraulic pump, with separate jack to avoid heat transmission to hydraulic parts.
automatic control of manufacturing cycles
preheating and curing time are controlled by a digital timer
switch for additional degassing
emergency stop
manometer for pressure control
2 PID electronic controllers securing perfect accuracy and distribution of temperature for pre-inked and rubber stamp making
platen sizes : standard : 350 x 300 mm or GF : 420 x 350 mm

PEVP press - A5

Moulding and vulcanizing presses used to press types or photopolymer plate in a matrix board and get a mold in which rubber is molded
Size A5 (270 x 230 mm)

A5 PRESS

pressure is provided by coupled pump and jack
2 PID electronic controllers secure perfect accuracy and distribution of temperature for pre-inked and rubber stamp making
Manual digital timer for cycle control

PEVP press - A4

Moulding and vulcanizing presses used to press types or photopolymer plate in a matrix board and get a mold in which rubber is molded
A4 (350 x 300 mm)

A4 PRESS

pressure is provided by separate pump and jack
2 PID electronic controllers secure perfect accuracy and distribution of temperature for pre-inked and rubber stamp making
Manual digital timer for cycle control
Manometer for pressure control on A 4 model.

LASER MANUFACTURING EQUIPMENT

ILS II

Available 12, 30 or 50 W, size 410 x 295 mm (A3).
Motorized Z axis allows to process pieces up to 120 mm
Air assistance

Consult our range of laser engravers

ILS III

Available in 12, 30 , 50 or 100 W, size 610 x 457 mm (A2)
Openable front door
Autofocus.
Motorized Z axis allows to process pieces up to 210 mm
Red dot pointer
Air assistance

Consult our range of laser engravers

ILS IV

Available in 30, 50 or 100 W, size t 1000 x 600 mm.
traversing-door design
Autofocus.
Motorized Z axis allows to process pieces up to 210 mm .
Red dot pointer
Air assistance
ethernet connectivity

Consult our range of laser engravers