| |
 |
| CONVENTIONAL
PRE INKED STAMP MAKING EQUIPMENT |
|
| Thermogravor | |
 | |
Photopolymer
machine to process photopolymer liquid resin or hard photopolymer plates (Rigilon,
Jet, etc)
size A 4, made of 3 parts : | | |
| Exposure unit | |
- to make a negative film from a laser printed positive
- to
expose a hard photopolymer plate through a negative and get a master plate
- to
expose photopolymer liquid resin through a negative and get photopolymer stamps.
|
| Wash-out unit |
- for hard photopolymer plates : exposed areas are left and create relief when
uncured parts are washed away (depth)
- for photopolymer liquid resin :
exposed areas are left and create letters when uncured parts are washed away (depth).
| | Drying unit |
- for negative film
- for hard photopolymer plate
after washing-out
- for photopolymer resin after washing-ou
|
|
| | | Automatic
press | |
 | |
Motorized moulding and vulcanizing press , size 350 x 300 mm, for rubber and
pre-inked stamp making
All manufacturing steps are automatically performed
. It is just necessary to set parameters (temperatures, preheating and cooking
times, cooking pressure) Then, pushing a single key will automatically start the
procedure : platen rising, contact during pre-heating time, degassing, pressure
and cooking , opening when programmed time is over. - Pressure by motorized
hydraulic pump, with separate jack to avoid heat transmission to hydraulic parts.
- automatic control of manufacturing cycles
- preheating and curing
time are controlled by a digital timer
- switch for additional degassing
- emergency
stop
- manometer for pressure control
- 2 PID electronic controllers
securing perfect accuracy and distribution of temperature for pre-inked and rubber
stamp making
- platen sizes : standard : 350 x 300 mm or GF : 420 x 350
mm
|
| PEVP press - A5 | |
 | |
Moulding and vulcanizing presses used to press types or photopolymer plate
in a matrix board and get a mold in which rubber is molded
Size A5 (270 x
230 mm)
A5 PRESS - pressure is provided by coupled pump and
jack
- 2 PID electronic controllers secure perfect accuracy and distribution
of temperature for pre-inked and rubber stamp making
- Manual digital timer
for cycle control
|
| PEVP press - A4 | |
 | |
Moulding and vulcanizing presses used to press types or photopolymer plate
in a matrix board and get a mold in which rubber is molded
A4 (350 x 300 mm)
A4 PRESS - pressure is provided by separate pump and jack
- 2
PID electronic controllers secure perfect accuracy and distribution of temperature
for pre-inked and rubber stamp making
- Manual digital timer for cycle control
- Manometer
for pressure control on A 4 model.
|
| Miscellaneous equipment | |
 | | Aluminium
casting chase :
used to fasten the mold and calibrate premix material
for gelling in the press.
Available in several sizes : (A4, A5, A6, A7) |
 | | Cooling
unit :
Providing fast cooling , necessary once premix is cured.
Flow
of water is controlled by timer and penstock
Size : A5 (270 x 230 mm) or A
4 (350 x 300 mm) |
 | | Stamp
cutter :
To cut each stamp from rubber or pre-inked slab |
 | | Vacuum
unit :
Vacuum chamber in which casting chase or chase board with premix
is placed.
A vacuum pump allows to release air bubbles thay may be trapped
in letters and that would cause non printing areas in the finish stamp.
Depression
is controlled by a vacuometer.
Size : 420 x 350 mm
| |
|
| LASER
MANUFACTURING EQUIPMENT |
|
| ILS II | |
 | |
- Available 12, 30 or 50 W, size 410 x 295 mm (A3).
- Motorized
Z axis allows to process pieces up to 120 mm
- Air assistance
|
| ILS III | |
 | |
- Available in 12, 30 , 50 or 100 W, size 610 x 457 mm (A2)
- Openable
front door
- Autofocus.
- Motorized Z axis allows to process pieces
up to 210 mm
- Red dot pointer
- Air assistance
|
| ILS IV | |
 | |
- Available in 30, 50 or 100 W, size t 1000 x 600 mm.
- traversing-door
design
- Autofocus.
- Motorized Z axis allows to process pieces
up to 210 mm .
- Red dot pointer
- Air assistance
- ethernet
connectivity
| | | | | |
